Please note that your hands must be dry when using this device. Wet hands will
make it difficult for the bio semi-conductor to read your fingerprint. Also be sure
to record one finger on each hand (in case of injury)
Setting The Admin Fingerprint
The Admin fingerprint will be able to add and remove any and all fingerprints from
the device. You are given 2 admin fingerprints, the 98 additional prints will be able to
use the lock, but they will not be able to delete or add users.
Slide up the cover + Press 2 (the red light will flash and the device will make a sound)
+ Place your Fingerprint onto the pad once until it beeps and then again (about 1
second later) until the red and green light flash 3 times. (If only the red light flashes
repeat the process, as your prints were not read correctly)
You will have to lift your finger after the first beep and then place it back on the pad
until your device beeps 3 times and flashes the Green and Red Light.
Setting The Second Admin Fingerprint:
Slide up the cover + Press 2 +place original admin fingerprint (green light will flash) +
Press 2 +New Admin Fingerprint.
You will have to lift your finger after the first beep and then place it back on the pad
until your device beeps 3 times and flashes the Green and Red Light.
To add user fingerprints:
Slide up the cover + Press 2 +admin fingerprint (either one-- The green light flashes
and the buzzer will make a sound.)+ new fingerprint (The green light and the buzzer
makes a sound) Press the fingerprint again, when successfully recorded the green and
red light will flash. (You’ll lift your finger right after your system blinks green and then
place your finger back on the pad).
If the device fails to record the print only the red light will flash.
To Delete All User Fingerprints
Slide up the cover+ Press 3 (Red light will flash)+ admin fingerprint (either one- green
light will flash)+”2222”+ 1 to confirm. Wait until the buzzer and green light flash 3
times.
Deleting a Single User Fingerprint via Fingerprint
Slide up the cover+ Press 3 (red light and buzzer will flash)+admin fingerprint (any one-
green light will flash)+the fingerprint that you want to delete. The green light will turn on
and the buzzer will make a long sound.
Deleting a Single Fingerprint Using the Fingerprint ID Code
Chart of Codes Are Located On Page 6.
Slide up the cover + Press 3 +admin fingerprint (either one)+ Fingerprint ID Code of
print you want to delete + Press 1. (See page 6 for information on ID Codes)
To Revise the Password
The original password is 23456
Slide the cover up+ Press 1(red light will flash with sound)+ Admin Fingerprint (Green
light will flash with sound) + your new password (must be between 6-12 digits from key
2, 3, 4, 5 or 6) + Press 1+ new password again + Press 1 to confirm
If the green light flashes and the buzzer makes 3 long sounds then you have successfully
changed the password.
Revising your new password:
Slide up the cover+ Press 1+admin fingerprint + new password(6-12 digits using keys
“2”, “3”, “4”, “5” and “6”) a red light will light up for every digit pressed + press 1+ re-
enter your new password + & press 1.
After 3 beeps and a green light you’re good to go.
Using your Password to Open the Lock
Slide up the cover + Press 1+ Enter Your Password (6-14 digits) + Press 1
Lets Say You’re Moving
And you want your door to be unlocked from the outside. You can press 6 + your
fingerprint +6 and your lock will go into docile mode. You will able to re-activate it
by simply using the device again.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales